1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION & OF THE COMPANY UNDERTAKING A Product Name Sovereign SBR Bonding Primer B Supplier Sovereign Chemicals Limited Park Road Barrow-in-Furness Cumbria. LA14 4QU C. Emergency Tel. No. 01229 870800 - Office hours 01785 272650 – Out of hours D. Appearance Milky white liquid emulsion E. Odour Slight 2. COMPOSITION/INFORMATION ON INGREDIENTS Key to proportions High 61-100%, Med 11-60%, Low 1-10%, Very Low <1% Key to identification: A = Chip Index No. B = EC No. C = CAS No. Component Classification R-Phrases Proportions Exposure Levels (8hr TWA) Identification Product is carboxylated styrene-butadiene rubber emulsion (47% solids content). 3. HAZARDS IDENTIFICATION There are no ingredients in this product in concentrations likely to constitute a hazard to health when handled correctly. 4. FIRST AID MEASURES EYES: Irrigate immediately with copious quantities of water for 15 minutes. Seek medical attention if symptoms persist. SKIN: Wash with water before the product dries. Dry product is removed with hot water or skin cleansers. Do not use solvents. If symptoms develop seek medical attention. INGESTION: Give water or milk to drink. Where large quantities are involved seek medical attention. Medical Practitioners may obtain further information from the National Poisons Information Centre. 5. FIRE FIGHTING MEASURES EXTINGUISHING MEDIA Water based product. All extinguisher types suitable. 6. ACCIDENTAL RELEASE MEASURES Spread inert absorbent to contain spillage. Prevent entry into streams, sewers or rivers. For disposal see section 13. Spillages into waterways must be reported to the Environmental Agency Incident Report Line (Tel: Freephone 0800 807060) 7. HANDLING AND STORAGE USAGE PRECAUTIONS: If affected by frost slowly bring to room temperature and stir. STORAGE PRECAUTIONS: Do not store in containers made of copper or aluminium or their alloys. STORAGE CRITERIA: Store between +5 and 35ºC. Protect from frost and sunlight. 8. EXPOSURE CONTROLS/PERSONAL PROTECTION EYES: Wear splash proof goggles conforming to BSEN 166 to avoid anypossibility of eye contact. HANDS, FACE, BODY: Use CE approved nitrile protective gloves RESPIRATORY: Good general ventilation is normally adequate. Engineering Controls of operator exposure may replace personal protective equipment if a C.O.S.H.H. Assessment shows a higher standard of protection. 9. PHYSICAL AND CHEMICAL PROPERTIES APPEARANCE: liquid COLOUR: milky white ODOUR: slight SPECIFIC GRAVITY: 1.01 pH: 9-10 PACKAGING 1 litre bottles TOTAL SOLIDS: 47% 10. STABILITY AND REACTIVITY STABILITY: Stable under normal storage conditions. 11. TOXICOLOGICAL INFORMATION INHALATION: Should not representa problem on correct use as instructed. Avoid breathing spray. SKIN: Frequent or prolonged contact may cause irritation. EYES: May cause slight irritation, redness and watering. MEDICAL CONSIDERATIONS: Small quantities ingested unlikely to cause more than temporary discomfort. 12. ECOLOGICAL INFORMATION Prevent entry into sewers, rivers or ditches. In high concentrations can prove harmful to fish and aquatic life. 13. DISPOSAL CONSIDERATIONS Allow to cure and dispose of via landfill. Use only licensed waste hauliers and disposal contractors. 14. TRANSPORT INFORMATION Not regulated for transport 15. REGULATORY INFORMATION Not Classified as Dangerous for Supply 16. OTHER INFORMATION EH40 Occupational Exposure Limits. Control Of Substances Hazardous To Health Regulations. HS(G)97 A Step by Step Guide to C.O.S.H.H. Assessment. Approved Carriage and Supply Lists. The Chemicals (Hazards, Identification, Packaging) Regulations This product should be stored, handled and used in accordance with good hygiene practices and in conformity with any legal regulations. The information contained herein is based on the present state of our knowledge and is intended to describe our products from the point of view of safety requirements. It should not be construed therefore as guaranteeing specific properties.